Dfi Q7-100 Instrukcja Użytkownika

www.d.comChapter 1 Introduction1Q7-100Qseven Carrier BoardUser’s ManualA19810337

www.dfi .comChapter 2 Hardware Installation10Chapter 2Clear CMOS DataIf you encounter the following,a) CMOS data becomes corrupted.b) You forgot the

www.dfi .comChapter 2 Hardware Installation11Chapter 2Backlight Control Level Select1321322-3 On: +3.3V1-2 On: +5V (default)JP15 is used to select the

www.dfi .comChapter 2 Hardware Installation12Chapter 2LVDS Power Select1-2 On: 12V6425316425316425313-4 On: 5V5-6 On: 3.3V (default)JP14 is used to sel

www.dfi .comChapter 2 Hardware Installation13Chapter 2VGA/DVI SelectThe system board allows connecting a device to either the DVI port or the VGA port

www.dfi .comChapter 2 Hardware Installation14Chapter 2BIOS SelectJ1 is used to determine the BIOS boot device. J11-2 On: Boot fromCarrier board SPI BIO

www.d.comChapter 2 Hardware Installation15Chapter 2Rear Panel IO PortsThe rear panel I/O ports consist of the following:• VGA port• DVI-D port• 2 COM

www.d.comChapter 2 Hardware Installation16Chapter 2DVI-I PortThe VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell

www.d.comChapter 2 Hardware Installation17Chapter 2RJ45 LAN PortsThe onboard RJ45 LAN port allows the system board to connect to a local area network

www.d.comChapter 2 Hardware Installation18Chapter 2Audio The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface f

www.d.comChapter 2 Hardware Installation19Chapter 2LVDS LCD Panel ConnectorLCD/Inverter Power ConnectorThe system board allows you to connect

www.dfi .comChapter 1 Introduction2CopyrightThis publication contains information that is protected by copyright. No part of it may be re-produced in a

www.d.comChapter 2 Hardware Installation20Chapter 2Digital I/O ConnectorDigital I/O Power ConnectorThe Digital I/O connector provides powering-on fun

www.d.comChapter 2 Hardware Installation21Chapter 2The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Se-rial A

www.d.comChapter 2 Hardware Installation22Chapter 2Chassis Intrusion ConnectorThe board supports the chassis intrusion detection function. Connect th

www.d.comChapter 2 Hardware Installation23Chapter 2Power ConnectorsUse a power supply that complies with the ATX12V Power Supply Design G

www.d.comChapter 2 Hardware Installation24Chapter 2The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of p

www.dfi .comChapter 2 Hardware Installation25Chapter 2DNG2 DNG 13 GBE_EBG4-3IDM_MDI2-5 GBE_EBG6+3IDM_MDI2+7 GBE_EBG8 -001KNIL_LINK1000- 9 GBE_EBG01-1ID

www.d.comChapter 2 Hardware Installation26Chapter 2The 1-channel I2C bus interface conforms to the version 2.1 I2C bus specification. It operates as

www.d.comChapter 2 Hardware Installation27Chapter 2USB Client ConnectorThe USB client connector supports 1 port (1 USB device controller with 1 port)

www.dfi .comChapter 2 Hardware Installation28Chapter 2LPC connectorThe Low Pin Count Interface was defined by Intel® Corporation to facilitate the indu

www.d.comChapter 2 Hardware Installation29Chapter 2SPI JTAG Connector127Pin Pin Assignment Pin Pin Assignment1 3V_standby 2 Ground3 CS 4 CK5 SO 6 SI7

www.dfi .comChapter 1 Introduction3Table of ContentsCopyright ...

www.d.comChapter 3 Supported Software30Chapter 3Chapter 3 - Supported SoftwareThe CD that came with the system board contains drivers, utilities and

www.d.comChapter 3 Supported Software31Chapter 3Realtek LAN DriversTo install the driver, click “Realtek LAN Drivers” on the main menu. 2. Click Inst

www.dfi .comChapter 1 Introduction4About this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, inser

www.dfi .comChapter 1 Introduction5About the PackageThe package contains the following items. If any of these items are missing or damaged, please cont

www.dfi .comChapter 1 Introduction6IO Connectors• 2 connectors for 4 external USB 2.0/1.1 ports• 1 LPC connector• 1 I2C connector• 1 CAN-bus connector•

www.dfi .comChapter 2 Hardware Installation7Chapter 2Chapter 2 - Hardware InstallationBoard LayoutBlock DiagramCOM 1COM 2VGADVI-IDVI-I port(DVI-D signa

www.dfi .comChapter 2 Hardware Installation8Chapter 2Mechanical Diagram211131 25 68123CA1170.0010.1646.94154.94160.020.0017.7536.9159.4389.62125.71151.

www.dfi .comChapter 2 Hardware Installation9Chapter 2Jumper SettingsCOM 0 RS232 SelectJP23 is used to configure COM 0 to RS232. The pin function of COM